五行創藝
  • 最新消息
  • 釉藥素坯
  • 美國陶藝土
  • 設備/工具
  • 課程體驗
  • 購 物 車
  • 會員專區
  • 聯絡我們

Laguna Dry Glaze Mixing Instructions

  • 首頁
  • 釉藥素坯
  • 商品說明
  • Laguna商品說明
  • Laguna Dry Glaze Mixing Instructions

釉藥素坯

  • 美國釉藥系列
    • Duncan 釉藥
      • CN想像釉下彩
      • CC化妝土
      • EZ彩繪釉下彩
      • IN想像釉
        • IN透明系列
        • IN不透明系列
        • IN 斑點系列
      • TM無光粉彩色釉
        • TM3 (低溫釉)
      • CR結晶釉系列
        • CR 結晶釉
        • CR 結晶粒
      • SN無光色釉
      • SY金屬釉
      • SH微光釉系列
      • 釉上彩
    • Laguna 釉藥
      • Cone06 低溫釉 (1000°C)
        • 人造鹽釉系列 Artifical Salt Glazes
        • 創新上釉系列 Creatable Colors
        • 彩釉系列 Cuerda Seca Glazes
        • 低溫亮面釉 Glossy Glazes
        • 低溫霧面釉 Satin Glazes
        • 月球表面霧面釉 Moonscape Glazes
      • Cone 5 中溫釉 (1200°C)
        • 裂紋釉 (透明) Crackle Glazes
        • 結晶釉 Crystal Blossom Glazes
        • 朝代釉系列 Dynasty Glazes
        • MS-摩洛哥沙無鉛釉 Moroccan Sand Glazes
        • LAGUNA 中溫無毒特殊無鉛釉 Mystic Glazes
        • 霧面釉系列 Satin Texture Glazes
        • MS-LAGUNA VERSA創新無鉛釉 Versa5 Glazes
      • 釉藥乾粉
        • 乾粉 Cone 1 Dry Glazes (1150°C)
        • 乾粉 Cone 5 Dry Glazes (1200°C)
        • 乾粉 Cone5-10 Dry Glazes (1200°C~1300°C)
        • 乾粉 Cone 10 Dry Glazes (1300°C)
        • 樂燒釉藥乾粉 Raku Dry Glazes
      • LAGUNA 釉下彩
  • Duncan素坯
    • 偶類
    • 盤類
    • 杯類
    • 花器類
    • 撲滿類
    • 其他類
    • 盒子類
    • 碗類
  • 商品說明
    • Duncan商品說明
      • Duncan目錄本
      • 了解Duncan
      • 使用Duncan釉藥問題
    • Laguna商品說明
      • Guidelines for Using Laguna Glazes
      • Laguna Dry Glaze Mixing Instructions
      • Dry Raku Glaze Mixing Instructions
Laguna Dry Glaze Mixing Instructions
     The following instructions and batch measurement guidelines are intended only as a general reference.
(Also, none of the information in this section applies to Laguna Raku glazes; refer to the raku glaze section for raku mixing instructions. Special mixing instructions for Mixing Moroccan Sand Satin Texture Glazes MS 125-134 are at the bottom of this page.)


General: Laguna's dry (powder) glazes are formulated for spraying or dipping over bisque. To adapt these glazes for brushing, add brushing medium (find in Raw Materials Section) to the dry glaze powder. Read carefully before mixing, write out your stepwise instructions before starting, formulate and mix per your glaze choice and specific application as indicated below. Wear appropriate gloves and mask while mixing your glaze. Approximately 8 to 11 ounces of water per pound of dry glaze will be needed, but the amount needed varies per glaze. Add additional water if glaze is too thick immediately after mixing. Some glazes gel when left undisturbed, mix aggressively before adding water during subsequent uses.

Low tech instructions (mixing with a dowel or narrow board)
     1.Measure 2/3rds of water into a clean plastic bucket. Reserve the other 1/3 of the water in a container which will allow you to pour it easily.
     2.Screen or sieve the dry glaze slowly into 2/3rds of the water in the bucket while continuously mixing. Scrape the sides and bottom of the bucket often and mix thoroughly.
     3.Check viscosity by dipping your gloved fingers and assess for appropriate thicknesses as described below.
  • clear dipping glazes (half and half consistency)
  • color dipping glazes (whole milk)
  • spraying (heavy cream consistency) 
  • brushing (yogurt consistency) mix brushing medium with dry glaze prior to water or replace a portion of the water with gum solution
     4.Screen through the appropriate mesh after blending with water to achieve the desired results. (Typically, 80-100 mesh sieve) Disregard if specific glaze instructions state not to sieve.
     5.For best results allow to sit for a period of 24 hours before being remixed and then applied.


Power mixer instructions (mixing with a variable speed drill and a mixing attachment)
     1.Measure 2/3rds of water into a clean plastic bucket. Reserve the other 1/3 of the water in a container which will allow you to pour it easily.
     2.Screen or sieve the dry glaze slowly into 2/3rds of the water in the bucket while continuously mixing. Scrape the sides and bottom of the bucket often and mix thoroughly. Add the remainder of the water in portions. Stir, shut off the drill and assess the thickness between each addition by dipping your gloved fingers and assess for appropriate thicknesses as described below.
  • color dipping glazes (whole milk)
  • clear dipping glazes (half and half consistency)
  • spraying and 60-65 for brushing (heavy cream consistency)
     3.When you see the approximate desired thickness, check viscosity with a hydrometer. The hydrometer reading should be approximately.
  • 55 for color dipping glazes
  • 46-47 for clear dipping glazes
  • 60 for spraying
  • 65 for brushing
     (Measuring a very thick material with a hydrometer can lead to a misleading result.)
     4.Screen through the appropriate mesh after blending with water to achieve the desired results. (Typically, 80-100 mesh sieve) Disregard if specific glaze instructions state not to sieve.
     5.For best results allow the mixed glaze to rest for a period of 24 hours before being remixed and then applying.


Batch Measurement Guidelines
     Mix a small batch to determine your optimum water content. For specific recommendations on how much water to add call 1-800-4Laguna.

Mixing MS 125-134 Moroccan Sand Satin Texture Glazes
     For best results add water and mix Satin Texture Glazes right before use. Due to the chemical composition of these glazes, they are best used right after they are mixed with water. When left sitting overnight after the water has been added, it is our experience they will 'jell up'. If water is added after 24 hours to correct the thickness, the glaze tends to crawl.

 

五行創藝設計有限公司

251新北市淡水區下圭柔山70-10號
電話:886-2-26251498|傳真:886-2-26267328
電子信箱:wxad@wxad.com.tw

五行創藝陶藝之友  官方LINE:  

加入好友
        
                                                                LINE           WECHAT
GO
訂閱
退訂
Design by 米洛網頁設計
Design by 米洛網頁設計